Varec TankGate Interface 8315 Series Manual de usuario Pagina 20
- Pagina / 120
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hardware TankGate Interface
10 Installation and Operations Manual
there is 230 mA of field power available. At +48VDC, there is 230 mA of field power
available.
Figure 2-8: Selection Jumper W3
2.2.2 Switches and Indicators
2.2.2.1 Reset push-button (SW3)
The RESET Switch is used to re-initialize the system hardware by causing it to go to a
known starting state. This switch may be pressed at any time; however, it will do the
following:
• Re initialize System Hardware
• Clear Scratch Memory
• Verify Database and Re initialize if Invalid
• Reset All Timers
• Enable Communications
Figure 2-9: Switches SW3 on the TankGate motherboard
Hard Reset
A special form of Reset is available for occasions when the battery backed-up data base
must be re initialized. This type of reset, the Hard Reset, can be performed before a
database is downloaded from a host PC.
Caution! The Hard Reset should be used as a last resort if the TankGate is not functioning. A
Hard reset clears the installed database. For the Hard Reset procedure, refer to the
Troubleshooting and Maintenance chapter.
EARTH
NEUTRAL
LINE
SURGE GND
A/TXD
B/RXD
GND
RTS
CTS
TXD
RXD
GND
+15V
+5V
GND
-15V
+
-
VFIELD
COM1
COM 0 AUX POWER
VFIELD=48V
VFIELD=24V
RESET
RS232
RS485
COM1
HARDWARE HANDSHAKING
A
B
VFIELD=48V
VFIELD=24V
J8
J7
W3
EARTH
NEUTRAL
LINE
SURGE GND
A/TXD
B/RXD
GND
RTS
CTS
TXD
RXD
GND
+15V
+5V
GND
-15V
+
-
VFIELD
COM1
COM 0 AUX POWER
VFIELD=48V
VFIELD=24V
RESET
RS232
RS485
COM1
HARDWARE HANDSHAKING
A
B
RESET
SW3
- Installation & 1
- Operations Manual 1
- Copyright 3
- Trademarks acknowledged 3
- Disclaimer of Warranties 4
- Terms of Use 4
- Safety Precaution Definitions 5
- Safety Precautions 5
- TankGate Interface 6
- Contents 7
- 8300 Contents 9
- Contents TankGate Interface 10
- 1Overview 11
- Overview TankGate Interface 12
- 1.4.9 Humidity 13
- 1.4.10 Storage temperature 13
- 2Hardware 15
- 2.1 Hardware Block Diagram 16
- 2.2 Motherboard Description 16
- 2.2.1 Power Supply 17
- Hardware TankGate Interface 18
- Figure 2-7: AC Power Fuse 19
- 2.2.2 Switches and Indicators 20
- 2.2.3 Communications 21
- Figure 2-12:Com1 SW2 Switch 22
- Figure 2-13:Com1 SW1 Switch 22
- 3.1 Features 25
- 3.2 Description 26
- 3.2.1 ID DIP Switch (SW1) 27
- 3.2.2 LED Indicators (D1-D6) 27
- Connect the field wiring 29
- 4.1 Software Features 31
- 4.1.2 Real-Time Clock 31
- 4.1.4 Communications 32
- 4.1.5 Protocols 32
- 4.1.6 Data Scanning Task 32
- 4.1.7 Database Manager 32
- 4.1.8 System Tasks 32
- 4.2 TankGate Software Blocks 33
- 4.3 Database Organization 34
- 4.4 Gathering Point Data 37
- Parameter Description 38
- 4.5 Modbus Communications 39
- 4.5.2 Fixed Modbus Map 40
- 4.5.3 GWBLK method 41
- 4.6 Clock (CLK) 44
- 4.7 Communications (COM) 45
- 4.7.2 Application 46
- 4.8.1 Parameters 47
- 4.9 Emulator (EMU) 48
- 4.9.2 Application 49
- 4.10 EMU Gateway (EMUGW) 50
- 4.10.2 Application 51
- 4.11.1 Parameters 52
- 4.11.2 Application 54
- 4.12 Gateway Block (GWBLK) 55
- 4.12.2 Application 56
- 4.12.3 Size Parameter 56
- 4.13 Integer Register (IREG) 57
- 4.14 Modbus Gateway (MODGW) 58
- 4.14.2 Application 59
- 4.15 Scaler Point (SCALER) 60
- 4.15.2 Application 61
- 4.16 System Information (SYS) 62
- 4.17.1 Parameters 63
- 4.17.2 Application 65
- 4.18.1 Parameters 66
- 4.18.2 Application 67
- 4.19.1 Parameters 69
- 4.19.2 Application 70
- 4.20 L&J Scanner (LJSCAN) 72
- 4.20.2 Application 73
- 5 Installation 75
- 5.3 Installation 76
- 5.3.1 Mounting the TankGate 77
- 5.3.2 Mounting the Enclosure 78
- 5.3.3 Select the Unit address 78
- 5.3.4 Wiring Up Power 78
- 5.3.5 Grounding 78
- 8300 Installation 79
- 6Using ViewRTU 81
- 6.4.1 ViewRTU window 83
- 6.5 The ViewRTU Menu Bar 83
- 6.5.1 The File Menu 83
- 6.5.2 The Point Menu 84
- Figure 6-7: Edit Point dialog 86
- 6.5.3 The Config Menu 87
- 6.5.4 The Communications Menu 89
- 6.5.5 The Options Menu 91
- 6.6 Using ViewRTU 93
- 6.5.6 The Help Menu 93
- 6.6.1 Overview 94
- 6.6.3 To modify a Value 97
- 8300 Using ViewRTU 101
- 7 Troubleshooting 107
- Communication 108
- 8300 Troubleshooting 109
- 7.3 Maintenance 111
- 1 Appendix 113
- 1.2.1 Modbus Map 114
- Your offical representative 120
- Your official representative 120
© 2020, manymanuals.es. Todos los derechos reservados | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales